Skip to main content

Industrial Coatings

Industrial and high-performance coatings

Floors and surfaces that take forklifts, chemicals, heat and constant traffic.

  • Free Quotes
  • Residential & Commercial
  • Local Melbourne Painters

What are industrial coatings?

Industrial coatings are protective systems applied to structural steel, plant, warehouse interiors and factory surfaces, chosen for how they perform against corrosion, abrasion, chemicals or temperature rather than for appearance. Preparation is typically mechanical, and the system is specified against the substrate and the conditions it has to survive.

Overview

Industrial coatings are specified, not chosen. What goes down depends on the substrate, what the floor carries, what gets spilled on it, how it is cleaned, and how long the site can be out of service while it cures.

Floor coatings in particular are unforgiving: preparation has to be mechanical, moisture in the slab has to be understood before anything is applied, and cure times are dictated by the product and the conditions rather than by the schedule.

Where a project depends on meeting a specific performance requirement — slip resistance, fire performance, chemical resistance or a workplace safety standard — that requirement is confirmed against the manufacturer’s product specification for the system being used, and any certification or testing needed is identified before work begins.

Summary

At a glance

Service
Industrial & High-Performance Coatings — Epoxy floors, slip-resistant systems, protective coatings and safety marking for working environments.
Surfaces and systems
Epoxy and polyurethane floor systems, Moisture-tolerant primers for slabs where vapour transmission is a factor, Aggregate and textured additives for slip resistance, Protective coatings for structural steel and plant and Line marking paints for internal and external traffic areas.
Where it is offered
Industrial Coatings is offered across Melbourne and surrounding suburbs, generally within about 40 km of Balwyn.
Quoting
Industrial Coatings is quoted in writing at no charge, after an inspection of the actual surfaces.

What we cover

What's included

  • Epoxy floor coatings

    Warehouse, workshop and plant room floors, over mechanically prepared and moisture-tested substrates.

  • Slip-resistant floor systems

    Aggregate and textured systems where slip resistance is required, specified to the manufacturer’s stated performance for the environment.

  • Protective and chemical-resistant coatings

    Systems selected for the specific exposure a surface faces rather than applied generically.

  • Safety paints and line marking

    Walkways, hazard marking, bay marking and equipment zones.

  • Fire-performance and heat-resistant systems

    Where a project calls for fire-performance or heat-resistant coatings, the system is selected against the manufacturer’s specification and any required documentation is identified up front.

  • Structural steel and plant

    Compatible metal surfaces prepared and coated with protective systems.

Our process

How the work runs

  1. Step 1: Assess the substrate

    Concrete condition, existing coatings, contamination and moisture all assessed, because a floor coating fails from underneath.

  2. Step 2: Confirm the requirement

    What the surface has to resist — traffic, chemicals, heat, moisture, slip — and any performance or documentation requirements for the site.

  3. Step 3: Mechanical preparation

    Grinding or shot blasting to achieve the profile the system requires. Chemical etching alone is generally not sufficient for a durable floor coating.

  4. Step 4: Repair and prime

    Cracks, joints and spalled areas repaired, then a primer suited to the substrate and its moisture condition.

  5. Step 5: Apply the system

    Build coats and topcoats applied to the manufacturer specification, within their stated temperature and humidity range.

  6. Step 6: Cure and return to service

    Return-to-service times are set by the product and the conditions. We confirm them for your system rather than promising a fixed figure.

Why it holds up

What you get

  • Substrate moisture assessed before a floor system is specified
  • Mechanical preparation rather than shortcuts
  • Systems selected against the actual exposure and cleaning regime
  • Return-to-service timing confirmed for the specific product used

Systems and materials

  • Epoxy and polyurethane floor systems
  • Moisture-tolerant primers for slabs where vapour transmission is a factor
  • Aggregate and textured additives for slip resistance
  • Protective coatings for structural steel and plant
  • Line marking paints for internal and external traffic areas

The specific products for your project are named in your written quote, so you know what is going on your property before you accept it.

Worth knowing

Where this needs assessing first

Before committing to this work

  • Steel preparation standards, coating thickness and recoat windows are properties of the specified system and are followed as the manufacturer defines them.
  • Corrosion that has caused section loss in structural steel is an engineering matter, not a coating one. It is identified and referred rather than painted over.
  • Work in an operating facility has to be planned around production, shutdowns and access to plant.
  • Where a coating must satisfy a standard or a rating, that requirement is identified at quoting stage so the correct system and application method can be selected and evidenced.

Questions

Common questions

If your question is not here, call and ask. We would rather explain it properly than have you guess.

  • How long will the floor be out of service?

    That depends on the system, the film build, the temperature and the humidity, and it is set by the manufacturer rather than by us. We confirm foot traffic and full-service times for the specific product before the job is scheduled, so the shutdown can be planned properly.

  • Can you guarantee a slip rating?

    Slip resistance is a property of the specified system as tested by its manufacturer, and it depends on the surface profile, the aggregate used and how the floor is maintained. We select systems against the manufacturer’s stated performance for your environment and will identify what testing or documentation your project requires, rather than making a blanket claim.

  • Do you provide fireproof coatings?

    Fire-performance coatings are highly specific products with defined application requirements and documentation. Where a project calls for one, the system is selected against the manufacturer’s specification and the certification and inspection requirements are confirmed before work starts.

  • Why does concrete need grinding rather than just cleaning?

    Floor coatings need a mechanical key and an open surface profile to bond to. Concrete has a dense, sealed surface layer, often with curing compounds or contamination in it. Grinding or shot blasting removes that layer and creates the profile the coating needs, which is why it is the single biggest factor in whether a floor coating lasts.

Where we work

Industrial Coatings across Melbourne

We work throughout Melbourne and surrounding suburbs, generally within about 40 km of the city. If your property sits outside that, ask — we travel for larger projects.

Balwyn · Brighton · Camberwell · Kew · Hawthorn · Malvern · Richmond · South Yarra · Toorak · Armadale · Canterbury · Surrey Hills

Free, no-obligation quotes

Get a written quote for your painting job

Tell us what needs painting and send a few photos. We will inspect the property and put a written, itemised quote in front of you — in Australian dollars, with the scope spelled out.

Optional measurement cookies

With your permission, Google Ads uses cookies and information about your visit to measure which ads lead to quote requests and phone-link clicks. Your quote details are not sent to Google. You can use the website without allowing this.

Change your choice through Cookie settings in the footer. Withdrawing permission reloads this page. Privacy policy