Skip to main content

Weatherboards

Weatherboard painting

Timber moves, and a coating on timber has to move with it. Preparation is what decides whether it does.

  • Free Quotes
  • Residential & Commercial
  • Local Melbourne Painters

What does weatherboard painting involve?

Weatherboard painting is the repainting of timber cladding and the trim around it, and most of the work is preparation rather than application. Boards are washed, scraped back to sound material, split and damaged sections are filled, bare timber is primed, and end grain is sealed — because end grain is where exterior paint on timber begins to fail.

Overview

Weatherboards expand and contract with heat and moisture, which puts constant stress on the coating. Add Melbourne’s UV exposure on north and west elevations and you have a surface that punishes shortcuts.

The failures are predictable: flaking along board edges, splitting at nail holes, and paint lifting at the bottom of boards where water sits and end grain draws moisture in. All of them are preparation problems before they are paint problems.

Summary

At a glance

Service
Weatherboard Painting — Timber cladding prepared back to a sound edge, with end grain sealed and boards primed.
Where it is offered
Weatherboards is offered across Melbourne and surrounding suburbs, generally within about 40 km of Balwyn.
Quoting
Weatherboards is quoted in writing at no charge, after an inspection of the actual surfaces.

What we cover

What's included

  • Timber inspection

    Boards checked for splitting, movement, moisture and decay before any coating is specified.

  • Removing failed coatings

    Loose and flaking paint scraped back to a sound edge and feathered so the transition does not show through.

  • Sanding and filling

    Bare timber sanded, splits and nail holes filled, and open joints sealed.

  • Priming and sealing end grain

    Bare timber primed and end grain sealed — the single most common point of early failure.

  • Weather-resistant finish coats

    Exterior systems selected for UV exposure and timber movement.

  • Heritage colour schemes

    Period-appropriate schemes for older Melbourne homes.

    Heritage colour schemes

Our process

How the work runs

  1. Step 1: Inspect the timber

    Every elevation assessed for coating failure, splitting, movement and any signs of decay or moisture ingress.

  2. Step 2: Wash

    Pressure washing to remove dirt, chalking and organic growth, then allowed to dry properly before work continues.

  3. Step 3: Scrape and sand

    Failed coatings removed back to a sound edge, bare timber sanded, and edges feathered so the repair is not visible under the finish.

  4. Step 4: Fill and seal

    Splits and nail holes filled, open joints and butt joins sealed with a flexible exterior sealant.

  5. Step 5: Prime

    Bare and repaired timber primed with an exterior wood primer, with end grain sealed wherever it is exposed.

  6. Step 6: Finish coats

    Weather-resistant coats applied within the manufacturer’s stated conditions, with attention to the bottom edge of each board.

Why it holds up

What you get

  • End grain sealed as standard rather than left exposed
  • Failed coatings feathered so the repair disappears under the finish
  • Open joints sealed before coating so water cannot get behind the boards
  • Work planned around weather rather than pushed through it

Worth knowing

Limitations and upkeep

Before committing to this work

  • Timber that has decayed rather than simply weathered needs replacing before coating. Paint over rot conceals it; it does not arrest it.
  • Boards that are cupping or splitting badly may indicate a moisture problem behind the cladding, which is worth resolving before a new coating is applied over it.
  • Coating timber in the wrong conditions causes problems that appear months later. Application is scheduled around temperature, humidity and the moisture content of the timber.
  • Where older layers may contain lead, preparation uses wet methods and containment rather than dry sanding.

Afterwards

Timber cladding rewards attention more than any other exterior surface, because the failures start small and in predictable places.

  • Check the ends of boards, around window frames and along fascias first. These fail before the flat faces do.
  • Wash the exterior periodically, particularly on elevations that stay damp or collect dirt.
  • Touch in a chip or a split as soon as it appears. Exposed timber absorbs water and the failure spreads under the surrounding film.
  • North and west-facing walls weather fastest in Melbourne and may need attention before the rest of the house does.

Questions

Common questions

If your question is not here, call and ask. We would rather explain it properly than have you guess.

  • Do you replace rotten weatherboards?

    Minor repairs, or coordination of repairs with a carpenter, can be discussed during the inspection. Where boards need replacing we will identify them and talk through how that gets handled before painting starts, so the work happens in the right order.

  • Why does paint keep flaking off the bottom of my boards?

    Almost always moisture. Water sits on the lower edge and is drawn into unsealed end grain, pushing the coating off from underneath. Sealing end grain and the bottom edge during preparation is what addresses it, not simply applying another coat.

  • Should weatherboards be sprayed or brushed?

    Both have a place. Spraying gives even coverage over large areas quickly, and back-brushing or back-rolling works the coating into the timber. The approach depends on the property, the access and the surrounding surfaces that need protecting.

  • Can I change to a much darker colour?

    Yes, though it is worth knowing that darker colours absorb more heat, which increases timber movement and puts more stress on the coating. It is a legitimate choice; it just makes preparation quality matter even more.

Further reading

Before you decide

Longer answers to the questions this work usually raises. No sales pitch — just what we would tell you on site.

Where we work

Weatherboards across Melbourne

We work throughout Melbourne and surrounding suburbs, generally within about 40 km of the city. If your property sits outside that, ask — we travel for larger projects.

Balwyn · Brighton · Camberwell · Kew · Hawthorn · Malvern · Richmond · South Yarra · Toorak · Armadale · Canterbury · Surrey Hills

Free, no-obligation quotes

Get a written quote for your painting job

Tell us what needs painting and send a few photos. We will inspect the property and put a written, itemised quote in front of you — in Australian dollars, with the scope spelled out.

Optional measurement cookies

With your permission, Google Ads uses cookies and information about your visit to measure which ads lead to quote requests and phone-link clicks. Your quote details are not sent to Google. You can use the website without allowing this.

Change your choice through Cookie settings in the footer. Withdrawing permission reloads this page. Privacy policy